• October 22, 2019, 02:14:46 am
• Welcome, Guest. Please login or register.
Did you miss your activation email?

!!

TEMAC Forum Guests

Please take the time to Register for the forum, especially if you are a TEMAC club member.

This is one of the most active RC club forums in Ontario. Please participate in the discussion to help our great club to continue to grow.

Author Topic: JETS DAY at TEMAC - Sunday May 19, 2019  (Read 616 times)

0 Members and 2 Guests are viewing this topic.

Offline GuyOReilly

  • Airman
  • **
  • Posts: 20
  • Karma: +0/-0
  • Real Name: Guy O'Reilly
  • Started Flying RC: 1998
Re: JETS DAY at TEMAC - Sunday May 19, 2019
« Reply #15 on: May 21, 2019, 12:30:01 pm »
Bruce;
Here is what a spin looks like in my Cessna Aerobat



 ;D


Offline Athol

  • Airman
  • **
  • Posts: 39
  • Karma: +0/-0
  • Real Name: Athol Cohen
  • TEMAC #: 264
  • Started Flying RC: 1974
Re: JETS DAY at TEMAC - Sunday May 19, 2019
« Reply #16 on: May 21, 2019, 01:15:04 pm »
Thanks Guy  :) So, to recover, do you kick the pedals the opposite way, and leave the nose down until the spin stops?

Offline GuyOReilly

  • Airman
  • **
  • Posts: 20
  • Karma: +0/-0
  • Real Name: Guy O'Reilly
  • Started Flying RC: 1998
Re: JETS DAY at TEMAC - Sunday May 19, 2019
« Reply #17 on: May 21, 2019, 01:51:34 pm »
Steps to recover do slightly change by model and aircraft type; however the same basic steps are involved:
1- Stop screaming!
2- Power idle and carburetor heat on
3- push down - not too long, just enough to recover from the stall, the plane will accelerate quite quickly, do not over speed (red line speed)
4- opposite rudder
5- ailerons neutral - very important else you may exacerbate the spin.
6- pull up once stall has been recovered and spinning stopped
7- Add full power - careful not to over speed the engine
8- Yell: YAHOO! once completed
9- Repeat as needed.

Offline Athol

  • Airman
  • **
  • Posts: 39
  • Karma: +0/-0
  • Real Name: Athol Cohen
  • TEMAC #: 264
  • Started Flying RC: 1974
Re: JETS DAY at TEMAC - Sunday May 19, 2019
« Reply #18 on: May 21, 2019, 01:53:11 pm »
Very good (and funny) especially the screaming!

Offline bweaver

  • Ace
  • *****
  • Posts: 1306
  • Karma: +7/-1
  • Real Name: Bruce Weaver
  • TEMAC #: 169
  • Started Flying RC: 1979
Re: JETS DAY at TEMAC - Sunday May 19, 2019
« Reply #19 on: May 21, 2019, 02:14:14 pm »
Re @GuyOReilly 's  video and subsequent instruction. Here is what a spin looks like in my Cessna Aerobat

Now that's just rubbing it in.  :P

Offline GuyOReilly

  • Airman
  • **
  • Posts: 20
  • Karma: +0/-0
  • Real Name: Guy O'Reilly
  • Started Flying RC: 1998
Re: JETS DAY at TEMAC - Sunday May 19, 2019
« Reply #20 on: May 21, 2019, 02:51:24 pm »
Just sharing a bit of knowledge, no rubbing whatsoever.  ;D